3d Printer Auto Ing Sensor 3d Touch Sensor Auto Bed Ing Sensor

199,00 RON
Livrare GRATUITĂ

3d Printer Auto Ing Sensor 3d Touch Sensor Auto Bed Ing Sensor

  • Marcă: Unbranded
Vândut de:

3d Printer Auto Ing Sensor 3d Touch Sensor Auto Bed Ing Sensor

  • Marcă: Unbranded

199,00 RON

Economii 60,00 RON (23%)

Preț recomandat

259,00 RON
În stoc
Livrare GRATUITĂ

Politica de retur pe 14 zile

Vândut de:

199,00 RON

Economii 60,00 RON (23%)

Preț recomandat

259,00 RON
În stoc
Livrare GRATUITĂ

Politica de retur pe 14 zile

Metode de plată:

Descriere

3d Printer Auto Ing Sensor 3d Touch Sensor Auto Bed Ing Sensor

Features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses, , metals and so on. The position of the point can be obtained by touching the point on the heated bed, and then compensated by adjusting the z-axis height during printing. The 3D-Touch auto leveling sensor is a device that uses the Hall defect to achieve leveling.The position of the point can be obtained by touching the point on the heated bed,and then compensated by adjusting the Z-AXIS height during printing,Printing can also be achieved even though the platform is not flat. The main functions and controls of 3D printer touch are the same as most auto bed leveling sensors, which consists of a RC servo and a -type switch,thus,3D printer touch can be used on 3D printer control board. By using progressively designed solenoid and hall sensor, it can integrate high precision in such a simple structure.To more -friendly and to bring you more enjoyable printing experience. NOTE: Pulling/pushing hardly on the -pin may damage Touch sensor and less accurate. Specifications: Current:15mA Max current (): 300mA Voltage: 5V Cable length: Short: 200mm Long: 1000mm Wire: 3pin: Green:-GND RED:+5V Orange: Signal cable 2pin: Black:-GND White:Z min Instructions 1.After receiving the module, do not install the module to the printer. First connect the signal wires of the module to the motherboard one by one. After power on, there will be a needle suction and needle action, which is normal. 2.When the main board and the module are powered on, do not plug and unplug the cables casually. be to connect when the power is off. 3.After the firmware setting is completed, it is still uncertain whether the setting is . You can manually trigger the module in advance to check whether the is operating normally. If it is abnormal, stop it in time and recheck the firmware . Prevent the probe from hitting the platform, causing damage to the module. size:17.70 x 12.80 x 2.90 cm :Metal + Plastic colour:White Package Contents: 1 * MKS 3D Printer Touch V2.0 Auto Leveling Sensor Only the above package content, other products are not included. Note: Light and different displays may cause the color of the item in the a little different from the real thing. The measurement allowed error is +/- 1-3cm.
  • ID Fruugo: 234782648-502151261
  • EAN: 694315524841

Livrări şi Returnări

Expediat în 24 de ore

  • STANDARD: GRATUIT - Livrare între vin. 02 ianuarie 2026–vin. 09 ianuarie 2026 - GRATUIT

Livrare de la China.

Facem tot ce ne stă în putinţă să ne asigurăm că produsele comandate de dumneavoastră vă sunt livrate în întregime şi conform specificaţiilor. Cu toate acestea, dacă primiţi o comandă incompletă sau articole diferite de cele comandate, sau aveţi alt motiv pentru care nu sunteţi mulţumit de comandă, puteţi returna comanda sau orice produse incluse în comandă şi primiţi o rambursare completă pentru articole. Vizualizaţi întreaga politică de returnare