High performance electronics - F7 55A power supply unit. Our BLITZ Mini F7 TwinG flight controls feature Gyro Fusion technology, a modern USB Type-C socket, 32MB of flash per tuning session and 5 UARTs for any device you want to use. Our new BLITZ Mini 55A ESC comes with better Mosfet cooling and a bunch of SMD capacitors to filter out any motor noise, plus direct mount capacitors pre-soldered right next to the battery cables. XING2 High Performance Motors - The Best Motors Just Get Better 7075 aluminum shroud, 5mm titanium shaft, NSK durable bearings, center slotted magnet (for better response) and lower air gap (for improved performance and efficiency) for higher magnetic flux. Not to mention the typical XING damping rings between the bell and the bearings to improve durability and make your flight smoother. Digital HD Experience - DJI Camera Vision Equipped with DJI Digital FPV System with 50mBit transmission capability, it enables 720P video streams on DJI FPV Goggles, which you can't achieve with old analog VTX. We use the new DJI Camera Vista HD system, mounted on the back of the quad. DJI cameras provide better image quality than other CaddX cameras. Better low-light performance and more detailed shadows. During the day, similar to the Nebula Pro, with improved dynamic range. Specification: - Overall Dimensions: 255.4mm (Squashed X) / 262.6mm (Dead Cat) - Geometry: Squashed X or DC (Dead Cat) frame available - Bottom to Top Distance: 28mm - Arm Thickness : 6mm - Bottom plate thickness: 3mm - Upper plate thickness: 3mm - Upper plank thickness (middle): 3mm - XING2 2506 1500KV motor (black) - HQ 6X2.5X3 three-blade propellers - Weight: 464.3g (without battery and GoPro mount) FC // Blitz Mini F7 (link) main feature: - Black box: 16MB - DJI Air Unit is plug and play. No need to solder small wires. - Bat, +5V, 3.3, start indicator - With LC filter. Specification: - Microcontroller: STM32 F722 - Gyroscope: BMI270 - Barrow: DPS310 - Betaflight OSD: IFLIGHT OSD (AT7456E) - Black box: 16MB - 5 X Uarts - UART1 for HD/Analog VTX - UART2 for Receiver - UART3, UART4 for GPS or other sensors requiring a serial port - UART6 for ESC telemetry - 4x PWM shot/output - 1I2C -1 9-pin SH1.0 connector for HD VTX/Analog VTX&CAM (5V/BAT/G/VO/T1 /R1/5V/G/VI) - 1xSH1.0 8pin ESC connector (R6/CUR/M4/M3/M2/M1/BAT/G) - 1xSH1.0 6pin connector for any receiver or DJI (3V3 /R2i/5V/G/R2/T2) - 1xSH1.0 4-pin GPS connector (T4/R4/G/5V) - 1 x SH1.0 4-pin LED and beep connector (BUZ/LED/G/5V) - Takes support Smartaudio & IRCTramp VTX protocol - WS2812ledStrip: yes - Beper: yes - Firmware: IFRC-BASEF4 4.XX - Mounting: 20*20mm/4 - Dimension: 30.5*27mm - Weight: 5.0g Specification: -Size : 35*42mm - Mounting hole: 20*20mm/4mm - Weight: 11.3 grams - Support g-input raisse 2-6S Microcontroller: G071 Constant: 55Amps Burst: 60Amps Current Sensor: Yes BEC: No Current Rate: 100 Support: DShot DShot150/300/600/MultiShot/OneShot etc. - Firmware: BLHeli 32 - Target: IFLIGHT_BLITZ_G1 Package included: - 1 x Nazgul Evoque F6 (Crushed X pattern or dead cat) - 4 x HQ 6X2.5X3 three-bladed propellers - 2 sets of drum pads - 1 x drum strap - 1 x screw bag