Feature 1The product can form a highstrength, wearresistant, highaccuracy standard female thread if you fit the wire screw set in the screw hole of the workpiece of aluminum alloy and other materials 2You can repaire the threaded hole in a costeffective manner. When a thread error occurs or a damaged female threaded hole is repaired, threaded insert is a repair method 3These steel wire inserts can be used to convert between metric and inch thread holes, which is convenient and fast 4A new type of female threaded fasteners. Adopt highstrength, highaccuracy diamondshaped crosssection steel wire. Also called threaded sheaths, stainless steel threaded sleeves, wire sleeves 5Works for improving thread strength and wear resistance significantly when used on lowstrength engineering materials such as aluminum alloy, zinc alloy, alloy, copper, plastic, engineering plastics, etc.Item Type: Thread InsertsMaterial: SUS304Model: M6x1Thread Specification: M6x1 (mm)Outside Diameter Before Installation: Approx. 7.5 ~ 7.9mm / 0.3 ~ 0.3inDiameter of Drilling Drill Bit for Installation: Approx. 6.3mm / 0.2in1.5D/2D/3D:Length After Installation: Approx. 9mm / 0.4in12mm / 0.5in18mm / 0.7inNumber of Turns Before Installation: 6.9/9.6/14.9Specification Description: For Example: M3x0.5X1.5D, which means that after the screw set is completed, the female thread is M3, the pitch is 0.5, and the length is 1.5D (length refers to 1.5 times the diameter, that is, 1.5x3=4.5mm ), the length here refers to the length after installation.How to Use:1. DrillingUse the drill bit of the size listed in the parameter table of the wire thread insert to drill the hole. Be careful not to drill the hole into a cone shape. The chips generated by the drill hole must be blown out with compressed air. After drilling, the counterbore should not exceed the depth of 0.4 pitch. Too large counterbore is not conducive to the screwing of the wire thread insert.2. TappingUse special taps for wire thread inserts to tap. The depth of the tapping must exceed the installation length of the thread inserts. After tapping, use a compressed air spraygunto blow out the debris. When the thread accuracy is high, check the tapped bottom hole with a special bottom hole plug gauge for wire thread inserts.3. InstallationPut the wire screw sleeve into the installation wrench (figure 5 on the right), insert the wire screw sleeve installation tail handle into the guide rodgrooveof the installation wrench, and turn the handle of the installation wrench to screw the wire screw sleeve into the screw hole. For installation of M14x2 or more phase thread thread inserts, you can use the "T" type slotting simple tool to install; Note: During the installation and screwing process of the thread inserts, there should be no pressing in the vertical direction to prevent jumping teeth. The correct method is slowly screw in the direction of thread rotation.4. Remove the handle (break off the mounting handle)Use a breaker to break the mounting handle. Use about 200g of coconut to hit the breaker instantly, and the handle can be removed. Do not use the mounting wrench to rotate in the opposite direction. Do not break the mounting handle. This situation is very easy. As a result, the tail shank was broken and the wire was pulled out.5. UnscrewWhen installation problems occur during the installation of the wire thread insert (such as jumping teeth), the thread insert needs to be removed, and a special sleeve remover should be used to remove the wire thread insert. .wang-edit-text{ font-family:'Arial' !important; } .wang-edit-text table { border-top: 1px solid #000; border-left: 1px solid #000; } .wang-edit-text table td, .wang-edit-text table th { border-bottom: 1px solid #000; border-right: 1px solid #000; padding: 3px 5px; } .wang-edit-text table th { text-align: center; }Package List100 x Thread Inserts