Sht30 Sht30-d Sht31 Sht31-d Sht35 Sht35-dsht40 Sht40-d Sht41 Sht41-d Temperature Humidity Sensor Breakout Weather For Arduino

319,00 RON
Livrare GRATUITĂ

Sht30 Sht30-d Sht31 Sht31-d Sht35 Sht35-dsht40 Sht40-d Sht41 Sht41-d Temperature Humidity Sensor Breakout Weather For Arduino

  • Marcă: Unbranded
Vândut de:

Sht30 Sht30-d Sht31 Sht31-d Sht35 Sht35-dsht40 Sht40-d Sht41 Sht41-d Temperature Humidity Sensor Breakout Weather For Arduino

  • Marcă: Unbranded

319,00 RON

Economii 230,00 RON (41%)

Preț recomandat

549,00 RON
În stoc
Livrare GRATUITĂ
Vândut de:

319,00 RON

Economii 230,00 RON (41%)

Preț recomandat

549,00 RON
În stoc
Livrare GRATUITĂ

Acceptăm următoarele metode de plată

Descriere

SHT30 Sensiron Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that have a true I2C interface for easy reading. The SHT30-D sensor has an excellent 2% relative humidity and 0.3C accuracy for most uses. Unlike earlier SHT sensors, this sensor has a true I2C interface, and (bonus ) even with two address options. It also is 3V or 5V compliant, so you can power and communicate with it using just about any microcontroller or microcomputer. Such a lovely chip - so we spun up a breakout board with the SHT30-D and some supporting circuitry such as pullup resistors and capacitors. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You'll need to solder the header onto the PCB but it's fairly easy and takes only a few minutes even for a beginner. Power Pins: Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V micro like Ard uino, use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V GND - common ground for power and logic I2C Logic pins: SCL - I2C clock pin, connect to your microcontrollers I2C clock line. This pin has a 10K pullup resistor to Vin SDA - I2C data pin, connect to your microcontrollers I2C data line. This pin has a 10K pullup resistor to Vin Pins: ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45 RST - Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset ALR - Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alerts SHT31 Sensiron Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that have a true I2C interface for easy reading. The SHT31-D sensor has an excellent 2% relative humidity and 0.3C accuracy for most uses. Unlike earlier SHT sensors, this sensor has a true I2C interface, and (bonus ) even with two address options. It also is 3V or 5V compliant, so you can power and communicate with it using just about any microcontroller or microcomputer. Such a lovely chip - so we spun up a breakout board with the SHT31-D and some supporting circuitry such as pullup resistors and capacitors. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You'll need to solder the header onto the PCB but it's fairly easy and takes only a few minutes even for a beginner. Power Pins: Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V micro like for Arduino, use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V GND - common ground for power and logic I2C Logic pins: SCL - I2C clock pin, connect to your microcontrollers I2C clock line. This pin has a 10K pullup resistor to Vin SDA - I2C data pin, connect to your microcontrollers I2C data line. This pin has a 10K pullup resistor to Vin Pins: ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45 RST - Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset ALR - Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alerts SHT40 Specifications: Power supply: 1.1-3.6V DC - typically 3.3V DC Resolution: 16bit Temperature measuring range: -40-125 C Temperature measurement resolution: 0.01 C Temperature measurement accuracy: 0.2 C Humidity measurement range: 0-100% RH Humidity measurement resolution: 0.01 RH Humidity measurement accuracy: 1.8% RH Sht41 is based on the newly upgraded CMOS ENSR chip, with lower power consumption Higher accuracy. The power supply voltage range is extended to 3.3 V to 5.0 V, which is very suitable for mobile applications and battery powered applications. output [2C Power supply voltage range 3.3 to 5.0 V average current 0.4ua (1 Hz measurement rate) Relative humidity operating range 0 to 100% RH Temperature operating range -40 to + 125 C (- 40 to + 257 f) Relative humidity response time 6 seconds (tau63%) Application: HVAC, dehumidifier, agriculture, cold chain storage, testing and testing equipmen
  • ID Fruugo: 360442330-783794964
  • EAN: 7574632014535

Informații privind siguranța produsului

Vă rugăm să consultați informațiile despre siguranța produsului specifice acestui produs prezentate mai jos

Următoarele informații sunt furnizate de comerciantul independent terț care vinde acest produs.

Etichete de siguranță pentru produse

CE Mark
Avertismente de siguranță: Not suitable for children under 24 months old,choking hazard,adult supervision required

Livrări şi Returnări

Expediat în 3 zile

  • STANDARD: GRATUIT - Livrare între mie. 05 noiembrie 2025–mie. 12 noiembrie 2025 - GRATUIT

Livrare de la China.

Facem tot ce ne stă în putinţă să ne asigurăm că produsele comandate de dumneavoastră vă sunt livrate în întregime şi conform specificaţiilor. Cu toate acestea, dacă primiţi o comandă incompletă sau articole diferite de cele comandate, sau aveţi alt motiv pentru care nu sunteţi mulţumit de comandă, puteţi returna comanda sau orice produse incluse în comandă şi primiţi o rambursare completă pentru articole. Vizualizaţi întreaga politică de returnare

Detalii de conformitate a produsului

Vă rugăm să consultați informațiile de conformitate specifice acestui produs prezentate mai jos.

Următoarele informații sunt furnizate de comerciantul independent terț care vinde acest produs.

Producător:
În continuare se prezintă informațiile de contact ale producătorului produsului relevant vândut pe Fruugo.

  • Shenzhen Yuntianying E-commerce Co., Ltd.
  • Shenzhen Yuntianying E-commerce Co., Ltd.
  • Room 20C, Building A, Block 8, North District
  • Shenzhen
  • CN
  • 518000
  • wulaiyouya@outlook.com
  • 13418789354

Persoana responsabilă în UE:
În continuare se prezintă informațiile de contact ale persoanei responsabile din UE. Persoana responsabilă este operatorul economic desemnat, cu sediul în UE, care este responsabil pentru obligațiile de conformitate referitoare la produsul relevant vândut în Uniunea Europeană.

  • BORCES JEREZ
  • YQY INTERNATIONAL CONSULTING
  • 5 Taiyun Road
  • 5 Taiyun Road
  • 5 Taiyun Road
  • Paris
  • FR
  • 214124
  • services@yqyic.fr
  • 13861750904
  • https://pfs-us.logisticsmngmt.com